RAYMARINE ST1000 MANUAL DOWNLOAD

Raymarine ST Plus Manual Online: Basic Installation. After establishing control dimensions A and B, you can usually mount the tiller pilot directly onto the . Manuals and documents for Raymarine product range. Manual Piloto Automático Raymarine ST / ST – Read more about manual, piloto, raymarine, yuluka and

Author: Mit Shanris
Country: Czech Republic
Language: English (Spanish)
Genre: Spiritual
Published (Last): 15 September 2009
Pages: 343
PDF File Size: 1.99 Mb
ePub File Size: 9.77 Mb
ISBN: 680-7-34884-757-7
Downloads: 8402
Price: Free* [*Free Regsitration Required]
Uploader: Samusho

December 5, at On start up the LCD screen displays before showing the course. This may be different from yours if you have a non-stock tiller or a kick-up rudder or yours is fastened to the rudder tighter than mine.

Release the keys and hold them in again for another 10 seconds until the display begins flashing the type setting. Unit raymarine st1000 manual display type setting, i. Have had a quick try at searching, but couldn’t find it.

December 5, at raymarine st1000 manual You are raymarine st1000 manual using your WordPress. I bought my Pearson 30 last august, and your website has been an inspiration to me.

Then, you can loosen the line, center the tiller, and retighten the line. So, to raise the tiller so that it is at least horizontal at its lowest position, I screwed a small teak stop block into the rudder underneath the aft end of the tiller handle. If it were my tiller, I would bore out the elongated holes oversize, fill them with raymarine st1000 manual epoxy, redrill the correct size holes raymarine st1000 manual manal cured epoxy, and attach the hardware with through bolts and sf1000 nuts.

Would you believe that a certain electronics service centre in my locality told me that it was a dealer service issue – I pressed him assuming that it might just be a jumper or dip switch or something on the pcb and explained I was happy to take it apart Glue the mounting socket Raymarine D, Defender special order part SPD, 5 pack in the hole with raymarine st1000 manual epoxy.

Manuals and Documents | Raymarine

What did you do to keep water out of the tiller-socket hole that was drilled into the boat? You might have to extend your framing square by clamping a straightedge to it. At first, my tiller sat angled raymarine st1000 manual slightly when in its lowest position. Which part you need, the pin or a bracket with raymarine st1000 manual, depends on your tiller and its height relative to where you will install the mounting socket for the stationary end of the Tiller Pilot.

How to Install a Tiller Autopilot – The $tingy Sailor

Next, use a framing square or similar tool held along the tiller shaft to find the point on the raymarine st1000 manual coaming that manaul exactly at a right angle from the tiller pin. Place masking tape on the coaming at this spot and make a small mark on the tape to show the point fore raymarine st1000 manual aft. Just brilliant – you guys are the best. Did the have an LCD screen?

I found that the Tiller Pilot worked noticeably better after setting those from the defaults. I love these forums! Draw raymarine st1000 manual circle around the mounting pin with it touching the coaming. Inserts are typically designed to provide in-line strength. I have a very dim memory of this coming up st10000 here in the past – I seem to recall raymarine st1000 manual the electronics are common to several models, and need to be told which body they’re in.

Anything more or less than that and your Tiller Pilot will turn farther in one direction than the other because the rod is either too long or too short.

You might need a helper for this raymarine st1000 manual. Notice the bracket nearby for storing the Tiller Pilot when not in use. You are commenting using your Twitter account. The Raymarine manual is pretty good and easy to find and download online.

Raymarine ST1000 & ST2000 Tiller Pilots

However, on a that I later owned, I can’t remember it displaying a model number on start up, so the display of that raymarine st1000 manual get seems odd. Email required Address never made public.

This point should be at raymarine st1000 manual degrees from the tiller pin when the tiller is aligned to raymarine st1000 manual center line of the boat.

With the tiller still held on the hull centerline, temporarily attach the Tiller Pilot rod onto the pin in the tiller bracket and hold the other end of the Tiller Pilot over your mark on the coaming with the mounting pin aligned vertically. All that remains is to wire power to the Tiller Pilot and, optionally, connect it to your GPS or chart plotter.

Mounting socket distance from tiller pin Now you can measure from the tiller pin to the centerline of the top of the starboard coaming.