EN ISO TOLERANCIAS · Norma ISO , Energia Sustentable · EN ISO TOLERANCIAS NORMA DE CALDERARIA ISO NORMA ISO Published on May | Categories: Documents | Downloads: | Comments: 0. views. NF EN ISO Welding – General tolerances for welded constructions. NF EN ISO Surface roughness characteristics of blast-cleaned steel substrates .
|Published (Last):||3 July 2007|
|PDF File Size:||6.38 Mb|
|ePub File Size:||1.63 Mb|
|Price:||Free* [*Free Regsitration Required]|
The actual size of an angle shall be determined by norma iso suitable measuring devices tangentially to the weldment, but away from the zone immediately influenced by the weld. General tolerances for linear and angular dimensions and for norma iso 13920 and position as specified in this standard apply for weldments, welding assemblies and welded structures etc.
A version norma iso any other norma iso 13920 made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the norma iso 13920 status as the official versions. The jso given in this standard are based on the principle of independency as specified in ISOac- cording to which the dimensional and geometrical toler- ances apply independently of each other.
NORMA ISO DOWNLOAD
NORMA ISO 13920 EBOOK
Range nkrma nominal sizes, I, in mm length or shorter leg 4. The results of measurement may be influenced if they are 1920 under unusual temperature or norma iso condi- tions e. Special provisions may be necessary for complex struc- tures. Figures 1 to 5 show examples of norma iso the shorter angle leg, I, is to be represented. The actual size norma iso an norma iso 13920 shall be determined by applying suitable measuring devices tangentially to the weldment, norma iso 13920 away from the zone immediately influenced by the weld.
A version in any other language made by translation under the responsibility of norma iso CEN member into its norma iso 13920 language and notified to the Central Secretariat has same status as the official versions. This does not apply to temporary dimensions. The distances between the actual surface and the measuring plane shall be measured example see figure 8.
Manufacturing documentation in which linear norma iso 13920 dimensions or indications for shape and noorma are pre- sented without individually indicated tolerances shall be deemed incomplete if there izo no, or norma iso 13920, reference to general tolerances. This European Standard isp be given the status of a national standard, either by publication of norma iso identical text or by endorsement, and conflicting national standards withdrawn, by February at the latest.
The distances between the actual surface and the measuring plane shall be measured example see figure 8.
Download Norma ISO –
Show related Norma iso at end. The deviation shall be derived from the difference between the nominal size and the actual size. The angular deviation may be measured in degrees and minutes, or in millimetres. Figures 1 to 5 show examples of how the shorter angle leg, I, norma iso 13920 to be represented.
The length of the leg may also be assumed to extend to a specified norma iso 13920 point. In this case, norma iso reference point Tolerance norma iso 13920 over isi shall be indicated on the drawing. The distance between the edge and the straightedge shall be measured for example, see figure 6.
No notes for slide. These nor- mative references are cited at the appropriate place in the text and the publications are listed hereafter.
Up-to—date lists and bibliographical references concerning such national standards may be obtained on application norma iso the Central Secretariat or to any CEN member.
The distance between the edge and the straightedge shall be measured for example, see figure 6. Tolerances for angular dimensions The length of the shorter angle leg shall norma iso 13920 nroma to deter- mine, on the basis of table 2, norma iso 13920 tolerances are to apply.
NORMA ISO 13920
The applicable tolerances are always those which are stated in the drawing. General tolerances for linear and angular dimensions and for shape and position as specified in this standard apply for weldments, welding assemblies and welded structures etc. Instead of specifying individual tol- erances, the tolerance classes according to this norma iso 13920 may be norma iso 13920.
Full Name Norma iso 13920 goes here.