IRFP360 DATASHEET PDF

IRFP datasheet, IRFP pdf, IRFP data sheet, datasheet, data sheet, pdf , International Rectifier, V Single N-Channel HEXFET Power MOSFET in a. The IRFP and IRFP are advanced power MOSFETs designed, tested, and guaranteed to withstand a specified level of energy in the breakdown. IRFP, SiHFP Vishay Siliconix. FEATURES. • Dynamic dV/dt Rated. • Repetitive Avalanche Rated. • Isolated Central Mounting Hole. • Fast Switching.

Author: Akinolrajas Nirisar
Country: Italy
Language: English (Spanish)
Genre: Software
Published (Last): 7 February 2018
Pages: 19
PDF File Size: 12.35 Mb
ePub File Size: 6.77 Mb
ISBN: 335-7-53043-681-9
Downloads: 78300
Price: Free* [*Free Regsitration Required]
Uploader: Gardat

Irfp360 datasheet option would be to use a phase controlled triac with MOC optocoupler. Which I’m guessing is your problem?

IRFP – Vishay – PCB Footprint & Symbol Download

I have considered the 12v led strip option, but the price would be much higher, irfp360 datasheet datzsheet I would need a supply at each 5 m and much more amps to drive. Can’t be that hard to find a 48V or so wall wart, that is a irfp360 datasheet of voltage to switch fast. The average current will increase because of the old “area under the curve.

Seekonk Super Contributor Posts: Please login or register. Nothing is quite like a great humming power-station. I am using the pwm from the atmega, the default hz is too small I would like hz or hz I was thinking the optocoupler cannot handle the switching and consider using irfp360 datasheet 6n is the 4n25 suited for this application or should I use something irfp360 datasheet Using a 6N and a MCP is the correct way to drive the mosfet, but using several kHz for driving a large led strip is not good and not necessary unless you add an inductor for irfp360 datasheet iffp360 current.

Use a logic level mosfetreason irfp360 datasheet normal type mosfet cannot be fully turned on by microprocessor output resulting in high resistance and heat built up in mosfet that’s why your circuit failed. The 4N25 is an analog optocoupler and is definitely orders of magnitude too slow. To simplify the layout, there are also optocoupler gate driver ICs which contain both in one package. Psi Super Contributor Posts: Did you miss your activation email?

You can use faster irfp360 datasheet coupler like 6N In software I always eliminate short pulses at either end which only cause heating. In a circuit like this with a irfp360 datasheet pull-down and an incredibly massive gate chargeyou’ll be lucky to succeed at 1kHz. There are very simple dimmers on internet.

I think people get into as much trouble with high speed drivers as they intend to solve. I have no trouble switching with opto isolators. Irfp360 datasheet transistor optoisolators, like 4N25, aren’t capable of switching much faster than a microsecond, suggesting a frequency below 50kHz. Check the pic again, He’s using 8.

Hello, I want to drive a V led strip using the IRFP mosfet for driving from an arduino pin I use a 4n25 optocoupler like the schematic attached. Life without Arduino still exist. If this is for dimming, you should use an even irfp360 datasheet ratio. Drop me a message! Dagasheet measured the dc voltage on the strip without and whit caps and there was a almost 50v difference if I recall right. For opto-isolation, if I recall even the 6N should be fast enough for irfp36 irfp360 datasheet, and can handle jrfp360 voltages than the 6N if 7V is too low irfp360 datasheet driving the gate of the FET.

What significance is the frequency? It may not be easy finding a irfp360 datasheet level FET capable irfp360 datasheet V and 10A as requested, what is the current consumption of the lighting strip when fully on? The 10K resistor is too high, make it 1K or under. BloodyCactus Frequent Contributor Posts: I think you would be better playing with lower voltages.

A room-sized installation will definitely be a source of EMI! Irfp360 datasheet tried running the optocoupler from a battery and same results.

Greek letter ‘Psi’ not Pounds per Square Inch.

Where is the 8. T3sl4co1l Super Contributor Posts: What purpose does it serve? I made a test setup like the img irfp360 datasheet without c1 it was irfp360 datasheet unstable.

What is the light string?

Like to see irfp360 datasheet little higher drive voltage to fully turn on the Irfp360 datasheet. The LED string will see the same maximum voltage with or without a capacitor. There is no need for the ohm which just reduces your drive. There was an error while thanking.

Please do not use this site with Internet Explorer

Thank you for the reply, by light string I mean an V led strip in the irfp datasheet I understood that the vgs is 10V the purpose is for irfp360 datasheet the led strip I use a rectifier datassheet so the led strip is irfp360 datasheet with DC could you recommend a logic level mosfet that can handle more than V dc and more than 10A current.

Try adding a capacitor after the rectifier to get a better dc voltage. I’m assuming you’re switching a DC light here. The flickering is probably the result of the PWM signal irp360 modulated by the mains frequency. What irfp360 datasheet the “8.