FLUKE 5500A CALIBRATOR MANUAL PDF DOWNLOAD

A. Multi-Product Calibrator. Service Manual. PN August Rev.5 , The Fluke Model A Multi-Product Calibrator (Figure ) is a precise. Fluke Corporation. 1. A Specifications. The following paragraphs detail specifications for the A Calibrator. changes more than 5 °C. (See “Zeroing the Calibrator” in Chapter 4 of the A Operator Manual.) Also see additional. 2 Fluke Corporation A/A Multi-Product Calibrators Extended Specifications. Warmup Time. Twice the time since last warmed up, to a maximum of

Author: Vudotaur Fautaur
Country: Netherlands
Language: English (Spanish)
Genre: Medical
Published (Last): 16 September 2004
Pages: 191
PDF File Size: 20.92 Mb
ePub File Size: 7.78 Mb
ISBN: 787-6-55960-583-7
Downloads: 96014
Price: Free* [*Free Regsitration Required]
Uploader: Kataur

Voltage Function A Service Manual Figure is a block diagram of the current function. Adjust A90R35 so that the second and third overshoot aberrations are the same amplitude as the first aberration.

fluke 5500a calibrator manual Resistance DC Offset Measurement 5500 you begin this procedure, verify that the A-SC is in the edge mode the Edge menu is displayedand program it to output 1 V p-p 1 MHz. Allow the A reading to stabilize. Then follow these steps to verify the leveled sine wave amplitude.

The fluke 5500a calibrator manual adjusts the harmonics. Adjusting the Leveied Sine Wave Harmonics Note This procedure should only be used for adjusting the leveled sine wave harmonics.

Determine that the SC falls within the typical specifications shown in Table Slowly adjust pot R57 and observe its effect on the first 15 ns of the waveform.

A dc reference voltage is supplied to the A5 1 board from the A6 DDS board; all dc and ac oscilloscope output voltages are derived from this signal and generated on the Fluke 5500a calibrator manual 1 board.

calibrahor Remove the power switch pushrod. Do not use this procedure as a verification test. DC Voltage Calibration This procedure uses the following equipment: The A then goes into Operate, or asks you to place it into Operate.

If it does not, repeat the aberration and rise time adjustments until you achieve the best compromise, within the listed tolerance levels. Also suspect is U31 on fluke 5500a calibrator manual A6 assembly. Thermocouple Measurement Accuracy Remove the top cover. Leaning the guidelines for handling them. Program fluke 5500a calibrator manual Calibrator Mainframe to output the voltage listed in Table AC Voltage Verification at 50 O Page – Oscilloscope Pulse Response Calibration Other suspects on the A6 assembly include relay K3 and resistor network Z5.

Then follow these steps to verify the MeasZ capacitance function. LCR Meter Connections omf. Capacitance, Four-Wire Comp For frequencies between kHz and Introduction This chapter contains an illustrated list of replaceable parts for the A Multi-Product Calibrator to the module level only. Fluoe will affect the first 50 ns of the wave form. fluke 5500a calibrator manual

Readjust A90R13 if neeessary to keep the edge signal at the reference level. Generating cluke Calibration Report Three different calibration reports are available from the A, each one either formatted for printing, or in comma- separated variable format for importation fluke 5500a calibrator manual a spreadsheet.

Fluke 5500A Calibrator – No Options

PtQ. Test points for these supplies are located in a fluke 5500a calibrator manual across the top of the Voltage fluke 5500a calibrator manual. For this test, measure the dc output at the A front panel Mamual connector with callibrator dc meter observe polarity on the TC connector.

Adjust R57 so the rising edge falls back and crosses the horizontal center line one division before the vertical center. Adjust A90R13 to set the edge signal at the right edge of oscilloscope display, at 10 ns, to the reference level set above. FR A7 Undercurrent fault You should perform the diagnositics in proper sequence.

Digital Multimeters (DMMs) and Precision DC Sources

The two boards are listed below. Then follow these steps to calibrate edge amplitude:.

The second harmonic will fluctuate, hut there is a point at which both harmonics will he at the correct decihel level. When you make this adjustment, the ledge will lose some of its flatness.

FLUKE a Calibrator repair help with IFC fet parts & data sheet – Page 1

There is not much room, but the cable is reachable. Thermocouple Measurement Accuracy The Thermocouple Measurement Accuracy test checks the internal temperature reference. To measure the phase, connect a 0. Figure shows the connections and the equation you use to calculate actual resistance. Low Frequency Flatness Verification at 5. Harmonics Page – Fluke 5500a calibrator manual Sinewave Verification: